Dexter Trailer Hub and Drum Assembly Installation 23-458- Video

Speaker 1: Today on our trailer we're gonna be doing a complete electric brake system overhaul. We'll be using Dexter electric trailer brake assemblies, part number 23-459 for the right side and the same Dexter brakes on the left side with part number 23-458. For our bearing and hub assemblies we'll be using Dexter's trailer drum and hub assembly, part number 8-219-4UC3-EZ.The best part about these brake assemblies is that they come preassembled so you just have to bolt them on. Assembling drum brakes can be a long, tedious task so you don't have to worry about it. The shoes included have bonded material so it'll give you a little bit extra life and prevent any rivets from digging into you drum if your brakes got stuck or you've worn them too far.They're electronically actuated so when power and ground is received here at the magnet it energizes it, causing it to grab, and the rotational force causes them to go outward into your drum, allowing you to stop. Since the are electric their replacement's a lot easier because you don't have to do any bleeding, it's a lot cleaner because there's no fluid, and it's fully adjustable with your brake controller up in the front. more

Watch Video

3/22/2018 11:54:50 AM

Dexter Axle Trailer Hubs and Drums - Hub - 84550BX Review- Video

more

Watch Video

3/16/2018 11:03:28 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-219-9UC3-A Review- Video

Speaker 1: Today we're gonna take a look at the Dexter 12-inch Trailer oil bath hub and drum assembly for 5,200-pound to 7,000-pound axles, with the 8 on 6-1/2" bolt pattern. Now this trailer hub and drum assembly are providing the surface area for your brake shoes to grip when your brakes are activated. It is compatible with both electric and hydraulic drum brakes.Now this hub and drum is designed for oil bath axles. It does include everything shown here on the table, the hub and drum assembly, both the inner and outer bearings. Now the bearing races are pre-installed. Right here is the outer, and over here is the inner bearing, right Comes with a unitized oil seal, the oil cap and then eight lug nuts. more

Watch Video

1/30/2018 12:10:28 PM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 84556UC3-EZ Review- Video

Speaker 1: Today we're going to take a look at the Dexter 10" Trailer Hub and Drum Assembly for 3,500 pound E-Z Lube axles with the 5 on 5" bolt pattern. Now this trailer hub and drum assembly will provide the surface area for your brake shoes to grip when the brake is activated. This is compatible with both electric and hydraulic drum brakes. This one is designed for E-Z Lube axles. And the E-Z Lube axles are the ones that will have the grease zerk fitting on the end of the spindle on the axle and that's to lubricate your bearings without having to remove the hub and drum assembly. This part will include everything shown here on the table. more

Watch Video

1/30/2018 8:49:27 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 84557UC3-EZ Review- Video

Speaker 1: Today we're going to take a look at the Dexter 10-inch trailer hub and drum assembly for 3,500 pounds E-Z Lube axles with the 5 x 5-1/2 inch bolt pattern. Now, this trailer hub and drum assembly will provide surface area for your brake shoes to grip when the brake is activated. It is compatible with both electric and hydraulic drum brakes. This one is also designed for use with the E-Z Lube axles and the E-Z Lube axles are the axles that will have the grease zerk fitting on the end of the spindle and that's used to lubricate your bearings without having to remove the hub and drum assembly.This part includes everything shown here on the table. The hub and drum assembly, both the inner and outer bearings, the bearing races which are already pre-installed in the hub, the double lip grease seal, the E-Z Lube grease cap and the five lug nuts. Now, the E-Z Lube compatible grease cap, it's nice because it makes lubricating your bearings very fast and easy. more

Watch Video

1/29/2018 1:49:35 PM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-219-50UC3 Review- Video

Speaker 1: inaudible 00:00:00. Speaker 2: Today we're gonna take a look at the Dexter 12-Inch Galvanized Trailer Hub and Drum Assembly for 5200-pound to 7000-pound axles, with the 8 on 6 1/2-inch bolt pattern. Now this is a marine-grade hub and drum assembly, which will fit axles with drum brakes. It includes everything shown here on the table, the hub and drum assembly itself, the inner, the outer bearings. Now the bearing races are pre-installed already into the hub. The grease seal, the grease cap, and the lug nuts are all included.This hub and drum assembly does have a Gal-Dex zinc plating, which is 500-hour salt spray rating. more

Watch Video

1/29/2018 10:44:27 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-219-50 Review- Video

Speaker 1: Today we're going to take a look at the Dexter 12" galvanized trailer hub-and-drum assembly for 5,200 pound to 7,000 pound axles has an 8 on 6-1/2" bolt pattern. Now, this is a marine grade hub and drum assembly that'll fit axles with drum brakes. It does include both the outer and inner bearing races already pre-installed, does require the inner and outer bearings, the grease seal, the grease cap and lug nuts for installation, those we do sell separately on our website and are listed on this product page with the correct part number that you need. This hub-and-drum assembly has a nice galvanized zinc plating to it, has a 500 hour salt spray rating. It's ideal for use on a boat or snowmobile trailer, and it is durable enough for saltwater applications.This is designed to work with 12" by 2" electric and hydraulic brake assemblies. The application on this, again, is 5,200 pounds, 6,000 pound and 7,000 pound axles. more

Watch Video

1/29/2018 9:34:19 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 84556UC3 Review- Video

Speaker 1: Today we're gonna take a look at the Dexter complete trailer hub and drum assembly for hydraulic brakes on a 3500 pound axle, and this has the five on five-inch bolt pattern. This hub and drum assembly will include everything shown here: the hub and drum itself, both the inner and outer bearings. Now the bearing races are included. They are pre-installed in the hub right there. Grease seal, the grease cap, the wheel studs are installed in the hubs, and then the lug nuts. All that's included.This is designed for use with the 10-inch by 2 1/4-inch hydraulic brake assembly. more

Watch Video

1/29/2018 7:54:21 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-389-81UC3 Review- Video

Speaker 1: Today we're going to look at the Dexter never lube trailer hub and drum assembly for 8,000 lb Dexter 50 millimeter never lube axles with the eight on six and a half inch bolt pattern.This hub and drum assembly will include the 50 millimeter cartridge bearing, the bearing retainers to keep it in there, the grease cap, the wheel studs and you notice the lug nuts are also included. This is designed to work with both electric, let me turn it around for you. Both electric and hydraulic brakes. It is for use with the 12 and a quarter inch by three and three eighths inch brake assemblies. Application again is the 8,000 lb Dexter 50 millimeter never lube axles. Capacity on this one is 4,000 lbs. more

Watch Video

1/26/2018 1:54:19 PM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-218-9 Review- Video

Speaker 1: Today we're going to take a look at the Dexter Oil Bath Trailer Hub and Drum Assembly for 8,000 pound axles. Has an 8 on 6 and 1/2 inch bolt pattern. Now this trailer hub assembly will fit 8,000 pound Dexter oil bath axles. Works with both electric and hydraulic brakes. It is designed to fit the 12 and 1/4 inch diameter by 3 and 3/8 inch wide brake drums.Now the inner and outer bearings, the oil seal, the oil cap are all sold separately, and on this product page it will list the part numbers that are needed. The bearing races are pre-installed in the hub. more

Watch Video

1/26/2018 1:05:16 PM

Dexter Axle Trailer Hubs and Drums - Hub - 8-214-5 Review- Video

Speaker 1: Today we're going to take a look at the Dexter Trailer idler hub assembly for 10,000 LB Dexter axles. This has an 8 on 6-1/2" bolt pattern. This trailer hub assembly is designed to fit 10,000 LB Dexter idler axles. It does fit the 12-1/4" diameter X 4" wide brake drums. The parts that you need with this are not included: the bearings, the oil seal, the oil cap, the wheel retaining ring, and the lug nuts are all sold separately. On the product page of this part number we do list the parts for those that you do need. more

Watch Video

1/26/2018 11:39:21 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-271-7UC3-EZ Review- Video

Speaker 1: Today we're going to take a look at the Dexter complete trailer hub and drum assembly for hydraulic brakes on a 2,000 pound EZ Lube axle. This has a 5 on 4-1/2" bolt pattern. Now this hub and drum assembly will include everything shown here on the table. It includes the hub and drum itself, both the inner and outer bearing. Now the bearing races are also included. They are pre-installed in the hub already. more

Watch Video

1/26/2018 10:19:23 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-276-5UC3 Review- Video

Speaker 1: Today we're going to take a look at the Dexter complete hub and drum assembly for hydraulic brakes on 2,200 pound axles, and this has the 4 on 4 inch bolt pattern. This part will include everything shown here. It includes both the inner and outer bearings. The bearing races are included, they are pre-installed into the hub. The grease seal is included, grease cap, the wheel bolts on the hub and then the four lug nuts. This is designed for use with the 7 inch by 1 3/4 inch hydraulic brake assembly only. more

Watch Video

1/26/2018 9:15:16 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-385-82UC3 Review- Video

Speaker 1: Today we're taking a look at a trailer hub and drum assembly. Now, this assembly is designed to be used on Dexter 50 millimeter never lube axles. This part number includes one assembly so, it comes with everything you see laid out here on the table.It has the snap rings, which are already pre installed. Bearings already pre installed. Comes with the lug nuts as well as the included cap, which goes over this area here and you just press fit that into position. The studs on the unit have a diameter of a half inch. more

Watch Video

1/16/2018 2:10:23 PM

etrailer Trailer Idler Hub Assembly Installation- Video

Speaker 1: Today we're gonna be taking a look at and showing you how to install trailer idler hub assembly for 3,500 pound axle, part number AKIHUB-545-35-K. This is also available in galvanized for marina applications, part number AKIHUB-545-35-G-K. This is also available in E-Z lube, part number AKIHUB-545-35-EZ-K. Also available in E-Z lube, galvanized for marina applications part number AKIHUB-545-35-G-EZ-K.This is what our hub assembly looks like installed on our trailer, it's gonna offer you an inexpensive, convenient way of having a complete new hub assembly where if you are looking to just replace your bearings you may have the added cost of hiring a shop to remove your old races from your old hubs in turn costing you more time and money by the time it's completed. Our hub kit is going to have the races already installed, it's gonna come with new bearings, new seals, caps, and new lug nuts, you're only gonna need grease and a few tools to get these installed.First thing we need to do to start our installation, I've gone ahead and removed the tire, we need to remove our hub. We're gonna remove this cap first, you're gonna take a small screwdriver and a mallet and we're gonna pop this cap off. more

Watch Video

12/28/2017 7:32:54 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Rotor - 008-416-91 Review- Video

Speaker 1: Today, we're taking a look at the Dexter 12-and-one-quarter-inch Oil Bath hub and rotor assembly. Now, this hub and rotor assembly works with 7,000 pound axles with disc brakes. It features machine processing, which all that's internally. That's gonna minimize run-out and warping. And what that means is that the contaminates can't get in-between the rotor and hub and cause damage. This is a cast-iron construction, which provides a lot of strength and durability.You'll notice that it has the vented design, which regulates temperature to prevent overheating. more

Watch Video

12/13/2017 12:55:31 PM

Dexter Axle Trailer Hubs and Drums - Hub - 8-213-5UC1 Review- Video

Speaker 1: Today we're gonna take at look at the Dexter Trailer Idler Hub assembly for 5,200 pound and 6,000 pound axles, with the six on five and a half inch bolt pattern. This hub assembly will fit trailer idler axle. Comes with everything shown here on the table. Comes with the hub assembly itself, both the inner and outer bearings. The bearing races are includes, they are pre-installed in the hub assembly already. The grease seal, the grease cap, and the wheel lug nuts are all included.This assembly is a sturdy iron construction. more

Watch Video

12/12/2017 11:30:32 AM

Dexter Axle Trailer Hubs and Drums - Hub - 84545BX Review- Video

Speaker 1: Today we're gonna take a look at the Dexter trailer idler hub assembly for 3,500 pound axles, with the 5 on 4-1/2 inch bolt pattern. Now this hub assembly is designed to fit trailer idler axles. Comes with everything shown here on the table. Comes with the hub assembly itself, the bearings, both inner and outer bearings. Now the bearing races are included, they actually pre-install them into the hub assembly. The grease seal is included, the grease cap, and the five wheel lug nuts are all included.This is a sturdy iron construction. more

Watch Video

12/12/2017 9:12:22 AM

Dexter Axle Trailer Hubs and Drums - Hub - 8-258-50UC1-EZ Review- Video

Speaker 1: Today we're going to take a look at the Dexter galvanized trailer hub assembly for 2,200 pound E-Z Lube Axles with the five on 4-1/2 inch bolt pattern. Now, this is a marine grade trailer hub assembly that fits idler axles. It includes everything shown here on the table. Comes with the hub assembly, the bearings, both inner and outer bearings, the bearing races, which already pre-installed in the hub. The grease seal, it's a double lip grease seal. The easy lube grease cap, and the zinc coated lug nuts.Now, this hub assembly has a gal-dex zinc plating to it, which has a 500 hour salt spray rating. more

Watch Video

12/11/2017 8:02:21 AM

Dexter Axle Trailer Hubs and Drums - Hub - 008-399-90 Review- Video

more

Watch Video

12/8/2017 8:48:29 AM

Dexter Axle Trailer Hubs and Drums - Hub - 8-214-5UC1 Review- Video

Speaker 1: Today we're going to take a look at the Dexter oil bath trailer idler hub assembly for 10,000 pound axles. Has the 8 on 6-1/2" bolt pattern. Now this trailer hub assembly is designed to fit idler axles and specifically it's designed to work on the Dexter 10,000 pound idler axles. This hub assembly is an oil bath design. What that means is it will let you check your lubricant level without disassembling the hub. Comes with this oil cap that screws in there. more

Watch Video

12/8/2017 8:34:51 AM

Dexter Axle Trailer Hubs and Drums - Hub - 8-288-3UC1 Review- Video

Speaker 1: Today we're going to take a look at the Dexter Oil Bath Trailer Idler Hub Assembly, for 9,000 pound to 10,000 pound axles. Has the eight on six and a half inch bolt pattern. Now this trailer hub assembly is designed to fit idler axles, it's designed to work with the Dexter 9,000 pound to 10,000 pound oil bath hub assemblies, and this is the oil bath design, which will let you check your lubricant level without disassembling the hub. Basically has the screw in clear oil cap right here that you can see through and check the lubricant level.Now the hub assembly itself is a sturdy iron construction. Does come with everything laid out here on the table, the hub assembly itself, the both inner and outer bearings, the bearing races which are pre-installed in the hub, the oil seal, the oil cap, the wheel retaining ring and the lug nuts are all included. This part is made in the USA. more

Watch Video

12/6/2017 1:55:22 PM

Dexter Axle Trailer Hubs and Drums - Hub - 8-258-50UC1 Review- Video

Speaker 1: Today we're going to take a look at the Dexter Galvanized Trailer Hub Assembly for 2,200-lb Axles with the 5 on 4 1/2" bolt pattern. Now this is a marine grade trailer hub assembly that will fit idler axles. It includes everything shown here on the table. It includes the hub assembly itself, both inner and outer bearings, the bearing races, which are already pre-installed into the hub, the grease seal, grease cap and the zinc coated lug nuts. Now the finish on this is a GAL-DEX zinc plating, which has a 500 hour salt spray rating. It is ideal for use on boat or snow mobile trailers and it is durable enough for even salt water applications.The application again is for 2,200-lb axles. more

Watch Video

12/6/2017 12:30:20 PM

Dexter Axle Trailer Hubs and Drums - Hub - 008-399-92 Review- Video

more

Watch Video

12/6/2017 7:33:29 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-430-5UC3 Review- Video

Speaker 1: Today we're taking a look at the Dexter trailer hub and drum assembly, this is a non-ABS drum. The trailer hub and drum assembly provides surface area for brake shoes to grip when the brake is activated.It is compatible with electric and hydraulic drum brakes. This is an oil bath assembly and so once you have it installed it has this clear cap that goes over the end here and that's gonna let you check lubricant level without disassembling the hub so you can look through the clear oil cap to check lubrication. It's a really nice design of the unit.It's made from a sturdy iron construction and it comes with everything that's needed so you have your inner and outer bearings, races are already installed, and the oil seal, the oil cap, you have the wheel retaining ring, the wheel bolts, as well as the lug nuts, all of that's included. This product is made in the USA, it's designed for Dexter 9,000 pound and 10,000 pound general duty axles and it'll fit a wheel size of 16 inches to 17 and a half inches.The bolt pattern on the unit, again these are already pressed into place, this is an eight on six and a half inch pattern. The pilot hole diameter is four and three-quarter inches, and when it comes to the drum size it's 12 and one-quarter by three and three-eighths. more

Watch Video

12/1/2017 11:35:26 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - K08-426-91 Review- Video

Speaker 1: Today we're taking a look at the Dexter Trailer Hub and Drum assembly for 4,000 pound easy lube axles. Now the Trailer Hub and Drum assembly provides surface area for the brake shoe to grip when the brake is activated this is compatible with electric hydraulic drum brakes. The easy lube compatible grease cap, which is this component right here, makes lubricating the bearings fast and easy. All you have to do is remove that rubber plug to gain access to the zerk fitting and then apply the necessary grease. There's no need to disassemble the hub. The unit is made from a very sturdy construction with protective finishing to keep it safe from rust and corrosion. more

Watch Video

11/30/2017 1:55:22 PM

etrailer Trailer Hubs and Drums - Hub - AKIHUB-865-7-1-EZ-K Review- Video

more

Watch Video

11/29/2017 11:33:29 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Rotor - 008-416-94 Review- Video

Speaker 1: Today we're going to take a look at the Dexter 12-and-a-quarter inch e-coat hub and rotor assembly with the eight on six-and-a-half inch bolt pattern for 7,000 pound Dexter axles. Now, this hub and rotor assembly is designed to work with 7,000 pound Dexter axles with disc brakes. The rotor itself has a machine process, which will minimize run out and warping. That will help keep contaminants from getting in between your rotor and your hub. The rotor is a van tip design you can see right here. That dissipates the heat, so it regulates temperature to prevent over-heating. more

Watch Video

11/2/2017 2:15:25 PM

Dexter Axle Trailer Hubs and Drums - Hub - 008-402-91 Review- Video

Speaker 1: Today we're taking a look at the Dexter never-lube trailer hub. This trailer hub is designed to work with an 8,000 pound axle. It's a cast iron construction, which provides strength and durability. It has a nice e-coat finish on it designed to protect it from rust, corrosion and wear. It comes with bearing, seals, races, lug nuts, the dust cap and the trailer hub. Everything that you need is included. more

Watch Video

11/2/2017 11:15:28 AM

Dexter Axle Trailer Hubs and Drums - Hub - 008-402-90 Review- Video

Speaker 1: Today we're taking a look at the Dexter Never-Lube Trailer Hub. This trailer hub is designed to work with an 8,000 pound axle. It's a cast-iron construction, which provides strength and durability, and it has an eco finish to protect against corrosion and wear. And it comes with the studs already installed and pressed in. Comes with all the necessary bearings, seals, races, lug nuts, dust cap, and of course, the trailer hub. The never-lube bearings come pre-lubricated and pre-installed. more

Watch Video

11/2/2017 10:56:40 AM

Dexter Axle Trailer Hubs and Drums - Hub - 008-399-93 Review- Video

Speaker 1: Today we're gonna take a look at the Dexter E-Coat Oil Bath Trailer Hub, with the eight on six and a half inch bolt pattern, for 8,000 pound axles. This trailer hub is designed to work with 8,000 pound axles with disc brakes. It is a cast iron construction, which will provide strength and durability. Has a nice e-coat finish over the whole hub to protect against corrosion and wear. And this part number will include everything shown here on the table. Includes the idler hub itself, the inner, the outer bearings. more

Watch Video

11/2/2017 10:50:28 AM

Dexter Axle Trailer Hubs and Drums - Hub - 008-399-91 Review- Video

Speaker 1: Today we're gonna take a look at the Dexter E-coat oil bath trailer hub with the eight on six and a half inch bolt pattern for 8,000 pound axles. This trailer hub is designed to work with 8,000 pound axles with disc brakes. It is a cast iron construction, provides strength and durability. It does have a nice E-coat finish on it to prevent against corrosion and wear, and this part does include everything laid out here on the table. It'll include the idler hub itself, the inner, the outer bearings. The bearing braces, they are actually pre-installed already into the hub. more

Watch Video

11/2/2017 10:30:29 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Rotor - 008-416-90 Review- Video

Speaker 1: Today we're going to take a look at the Dexter 12-1/4" E-coat Hub-and-Rotor Assembly with the 8 on 6-1/2" bolt pattern for 7,000 pound Dexter axles. Now, this whole Hub-and-Rotor Assembly will work with 7,000 pound Dexter axles with disc brakes. They do use a machine process to help minimize runout and warping. It helps keep contaminants so it can't get in between your rotor and your hub. The hub and the rotor itself has a vented design to dissipate heat. This will regulate temperature and prevents overheating. more

Watch Video

11/2/2017 9:40:28 AM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Rotor - 008-416-92 Review- Video

Speaker 1: Today, we're taking a look at the Dexter 12 and one quarter inch hub and rotor assembly. This hub and rotor assembly is designed for use with disc brakes on a 7000 pound axle. It goes through a machine process which is designed to minimize run out and warping. Also, contaminants can't get in between the rotor and the hub because of that machine process. It's got a nice vented design on it as well, which regulates temperature to prevent overheating. The wheel studs, lug nuts, bearings, races, grease seal, and grease cap are all included.When it comes to the construction, it's a cast iron construction, which provides strength and durability, and it has an eco-finish, which is designed to protect it against corrosion and wear. more

Watch Video

11/2/2017 9:26:46 AM

Titan Trailer Hubs and Drums - Hub - T1721400042 Review- Video

Speaker 1: Today we're going to take a look at the Titan Trailer Hub Assembly for 2500 pound axles. This has a five on four and a half inch bolt pattern. Now this is a cast trailer hub assembly and it's designed to fit 2500 pound idler axles. This kit will come with everything you need, the bearings, the bearing races which are pre-installed, the grease seal, the grease cap and the lug nuts are all included.Again, the bolt pattern on this is a five on four and a half inch. Weight capacity on this hub is 1,250 pounds, so when this one's used with one on the other side of the axle, it'll meet your 2500 pound axle capacity. Now the bearings that are included are the inner bearing, which is part number LM67048, outer bearing, which is LM11949. more

Watch Video

10/3/2017 8:21:57 AM

Kodiak Trailer Hubs and Drums - Hub with Integrated Rotor - KHR1389 Review- Video

Speaker 1: Today we're gonna take a look at the Kodiak 13 inch Hub and Rotor in a raw finish. Eight on six and a half inch bolt pattern, for 7000, 8000 pound axles. Now this is a single piece assembly so it makes installation a snap whether you're retro fitting or just switching from drum brakes. Does use a machine process that'll minimize run out and warping, so contaminants can't get in between your rotor and your hub. It is a balanced unit, provides a nice smooth ride. And it is also a vented design right here you can see, this will effectively dissipate heat, prevents any heat related damages. more

Watch Video

9/29/2017 10:45:23 AM

Kodiak Trailer Hubs and Drums - Hub with Integrated Rotor - KHR138XL10 Review- Video

Speaker 1: Today we're gonna take a look at the Kodiak 13-inch XL-Lube hub and rotor in a raw finish. Has an eight on six and a half inch bolt pattern, and it's for 8000 pound axles. Now this single piece assembly will make installation a snap, whether you're retro-fitting or switching from drum brakes. This uses a pre-lubricated 50 millimeter sealed bearing cartridge, which is pressed into the hub after factory. The sealed bearing includes the seal in the inner and outer race, so there's no need to replace the seal when you're checking your brakes, or no need to lubricate your bearings.The machine process on this helps minimize runout and warping. Contaminates can't get in between the rotor or the hub. more

Watch Video

9/29/2017 9:55:13 AM

Kodiak Trailer Hubs and Drums - Hub with Integrated Rotor - KHR138XL9E Review- Video

Speaker 1: Today, we're gonna take a look at the Kodiak 13" XL lube hub and rotor. Has a nice E coat finish, eight on 6 1/2" bolt pattern for 8000 pound axles. Now this single piece assembly makes installation a snap, whether you're retrofitting or switching from drum brakes. It does use a pre-lubricated seal. 50 millimeter bearing cartridge. It's pressed into the hub at the factory. more

Watch Video

9/29/2017 9:41:59 AM

Kodiak Trailer Hubs and Drums - Hub - KH42655S Review- Video

Speaker 1: Today we're gonna take a look at the Kodiak Stainless Steel Trailer Hub for 5,200 pound to 6,000 pound axles. Has a six on five and half inch bolt pattern. Now this is a rust-proof stainless steel hub. It's ideal for extended marine use. This trailer hub assembly can be used on an idler axle or it can be paired with a 12-inch slip on rotor for disc brake application. The wheel studs on these are long enough to accommodate an over the hub brake rotor. more

Watch Video

9/15/2017 10:07:06 AM

Kodiak Trailer Hubs and Drums - Hub - Q-HUB84545 Review- Video

more

Watch Video

9/5/2017 2:48:27 PM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-285-9UC3 Review- Video

Speaker 1: Today we're going to take a look at the Dexter Oil Bath Trailer Hub and Drum Assembly with the 8 on 6-1/2" bolt pattern. Now the application for this hub and drum assembly is 8000-lb Dexter Axles. By spinning this around I'll show you inside, you can see that it will work with both electric and hydraulic brakes. The drum dimension on this is going to be the inside diameter is 12-1/4". The width on it is right at 3-3/8" wide. Again the bolt pattern on this is an 8 on 6-1/2" bolt pattern. more

Watch Video

8/9/2017 3:11:16 PM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-201-5 Review- Video

Speaker 1: Today we're going to take a look at the Dexter trailer hub and drum assembly for 5,200 pound axles which has a 6 on 5-1/2 inch bolt pattern. Now the application for this is 5,200 pound Dexter axles with spindles that'll require a 2-1/8 inch or 2-1/4 inch inside diameter grease seal. This is designed to work with both electric and hydraulic brakes. The drum dimension on this is 12 inches in diameter and 2 inches in width. The diameter would be measured inside to inside. So there's your 12 inches. more

Watch Video

8/9/2017 7:00:13 AM

etrailer Trailer Hub and Drum Assembly Installation akhd-865-7-2-ez-k- Video

Today we're going to take a look at, and show you how to install the etrailer hub-and-drum assembly for the 7,000-lb E-Z Lube axles. Part number is AKHD-865-7-2-EZ-K. Now our kit's gong to contain everything we're going to need for basically one half of an axle. We're looking at brakes that are sized at 12" by 2" thick. That's what this is designed to fit, and the bolt pattern will have eight studs, and these are on what they call a 6-1/2" bolt pattern. So if that matches the hubs that are on your trailer, this is going to be a great fit for ya. more

Watch Video

7/13/2017 5:52:14 PM

Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 845476UC3 Review- Video

more

Watch Video

6/12/2017 7:33:39 AM

CE Smith Trailer Hubs and Drums - Hub - CE13100 Review- Video

more

Watch Video

5/25/2017 2:33:24 PM

CE Smith Trailer Hubs and Drums - Hub - CE13109 Review- Video

Today we're going to take a look at the CE Smith Pregreased Trailer Hub Assembly with the carrying case for 2700 pound axles and a 4 on 4 inch bolt pattern. When you receive it you'll get it just like this in this nice hard carrying case. This kit will let you replace one hub assembly on your trailer. We'll pop it open here and we'll show you the hub assembly itself right here. It includes the bearings pre-installed, the bearing races, the grease seal. In a separate bag it will have the grease cap, the lug nuts and the cotter pin. Comes in this nice hard plastic carrying case with this nice handle. more

Watch Video

1/24/2017 10:04:06 AM

CE Smith Trailer Hubs and Drums - Hub - CE13110 Review- Video

Today we're going to take a look at the C.E. Smith pre-greased trailer hub assembly with the carrying case for 2,500 lb axles with the four on four inch bolt pattern. This kit will let you replace one hub assembly on your trailer. Comes just like this in this nice hard carrying case. Just flip it open. This kit will include the bearings, the bearing races and the grease seal, all the hub right here. Then in a separate bag it includes your grease cap, your lug nuts and your cotter pin. more

Watch Video

1/24/2017 10:02:59 AM

Titan Trailer Hubs and Drums - Hub - T4084600042 Review- Video

Today we're going to take a look at the Titan trailer hub assembly for 2,000 pound axles with the 5 on 4-1/2" bolt pattern. This is a Cast trailer hub assembly that will fit on idler axles. It includes everything here. It includes the bearings, the bearing races, which are pre-installed in the hub, the grease seal, the grease cap and the lug nuts. Application on this is for 2,000 pound axles. It may also be used on 2,500 pound axles that have a 1" spindle. The bolt pattern this has is a 5 on 4-1/2" bolt pattern. The wheel studs are a 1/2" diameter, and the weight capacity on this one assembly is 1,250 pounds. The parts it comes with I want to go through. more

Watch Video

1/20/2017 11:35:11 AM

CE Smith Trailer Hubs and Drums - Hub - CE13511 Review- Video

Today we're going to take a look at the CE Smith pre-greased trailer hub assembly with the hard carrying case for 3500 pound axles with the five on four and a half inch bolt pattern. You'll receive it just like this in this nice hard carrying case. When you open it up it will include a nice pre-greased hub assembly that uses heavy duty marine grade lubricant, which is ideal for boat trailers. A hard carrying case with a handle keeps all your parts in one place. It has a separate bag which will have the grease cap, the lug nuts, and the cotter pin in. Go ahead and open this up. We'll reach in and pull it out so you can get a better view of it. more

Watch Video

1/20/2017 10:53:59 AM

CE Smith Trailer Hubs and Drums - Hub - CE13210 Review- Video

Today we're going to take a look at the C.E. Smith Pre-Greased Trailer Hub Assembly in this hard carrying case for 2,500-lb axles with the 5 on 4-1/2" bolt pattern. Now, this is a pre-greased hub assembly as uses heavy-duty marine-grade lubricant, which is ideal for boat trailers. See, it comes all wrapped in here. Everything comes pre-installed. Now this kit will let you replace one hub assembly on your trailer. It includes the bearings, the bearing races, the grease seal, the grease cap. more

Watch Video

1/20/2017 10:34:01 AM

  4     5     6